Skip to content
StockGauge Metal gauge · plate · bar · pipe

18 Gauge Stainless Steel Thickness and Weight

A 18 gauge stainless steel sheet is 0.0500 in (1.270 mm) thick. At 8,000 kg/m³ (0.2890 lb/in³) it weighs 2.081 lb/ft² (10.16 kg/m²), so a 4×8 ft sheet weighs 66.6 lb (30.2 kg) and a 1250×2500 mm sheet weighs 31.8 kg (70.0 lb).

Thickness
0.0500 in · 1.270 mm
Weight per ft²
2.081 lb
Weight per m²
10.16 kg
4×8 ft sheet
66.6 lb · 30.2 kg
1250×2500 mm sheet
31.8 kg · 70.0 lb
Density used
8,000 kg/m³ · 0.2890 lb/in³

Sheet metal gauge & plate weight calculator

Mode

Stainless Steel Gauge (U.S. Standard progression). Same nominal weights as MSG, divided by 40 lb/ft² per inch. Density 8,000 kg/m³ = 0.2890 lb/in³. Rounded handbook value for austenitic 304 and 316 (published figures cluster around 8,000 kg/m³).

Thickness

0.0500 in

1.27 mm

Per ft²

2.081 lb

10.16 kg/m²

4 × 8 ft sheet

66.59 lb

30.20 kg

1250 × 2500 mm

31.75 kg

70.00 lb

Gauge standard
Stainless Steel Gauge (U.S. Standard progression)
Thickness
0.0500 in · 1.270 mm
Nearest gauge
18 ga on the Stainless chart
Density
8,000 kg/m³ (0.2890 lb/in³)
Weight per ft²
2.081 lb
Weight per m²
10.16 kg
4 × 8 ft (48 × 96 in) sheet (32 ft²)
66.59 lb · 30.20 kg
1250 × 2500 mm sheet (3.125 m²)
70.00 lb · 31.75 kg

Worked calculation

  1. Look up the thickness. Stainless Steel Gauge (U.S. Standard progression), 18 ga = 0.0500 in. In millimetres: 0.0500 × 25.4 = 1.270 mm.
  2. State the density. Stainless Steel 304 / 316: 8,000 kg/m³ = 0.2890 lb/in³ (1 lb/in³ = 27,679.9 kg/m³).
  3. Weight per square foot. 0.0500 in × 144 in²/ft² × 0.2890 lb/in³ ≈ 2.081 lb/ft².
  4. Weight per square metre. 1.270 mm × 8.00 kg/m²/mm (density ÷ 1,000) ≈ 10.16 kg/m².
  5. Weight of a 4×8 ft sheet. 2.081 lb/ft² × 32 ft² ≈ 66.6 lb (30.2 kg). For a 1250×2500 mm sheet: 10.16 kg/m² × 3.125 m² ≈ 31.8 kg.
  6. Compare with the published chart weight. MSG defines 18 ga as 2.000 lb/ft² nominal (0.0500 in × 41.82 lb/ft² per inch). The density-based 2.081 lb/ft² is -3.9% lower because 7,850 kg/m³ equals 40.84 lb/ft² per inch, not 41.82.

Reference tables

18 gauge in each chart (density-based weights)
ChartThickness (in)Thickness (mm)lb/ft²kg/m²4×8 ft sheet (lb)
Manufacturers' Standard Gauge (MSG) 0.04781.211.9529.5362.5
Stainless Steel Gauge (U.S. Standard progression) 0.05001.272.08110.1666.6
Brown & Sharpe / American Wire Gauge (AWG) 0.04031.020.5662.7618.1
Galvanized Sheet Gauge 0.05161.312.10710.2967.4

The same gauge number gives a different thickness in every chart.

Stainless gauges around 18 ga
GaugeThickness (in)Thickness (mm)lb/ft²kg/m²4×8 ft sheet (lb)
16 ga 0.06251.592.60112.7083.2
17 ga 0.05631.432.34311.4475.0
18 ga 0.05001.272.08110.1666.6
19 ga 0.04381.111.8238.9058.3
20 ga 0.03750.951.5617.6249.9

Engineering and fabrication notes

18 gauge stainless steel is 0.0500 in (1.27 mm), a clean 0.050 in, and weighs 2.081 lb/ft². It is a typical choice for backsplashes, shelving, hoods and ductwork in food-service work, equipment doors and light enclosures, where corrosion resistance is the reason for using stainless and strength is secondary. Against carbon steel 18 gauge (0.0478 in) it is about 4.6% thicker and 6.6% heavier per square foot, so a stainless swap changes part weight and sheet cost even though the gauge number is unchanged.

Frequently asked questions

What is the thickness of 18 gauge stainless steel?

18 Gauge Stainless Steel is 0.0500 in or 1.27 mm on the Stainless Steel Gauge (U.S. Standard progression) chart. Same nominal weights as MSG, divided by 40 lb/ft² per inch.

How much does a 4×8 sheet of 18 gauge stainless steel weigh?

A 4×8 ft (48 × 96 in) sheet of 18 gauge stainless steel weighs about 66.6 lb (30.2 kg) using 8,000 kg/m³. That is 2.081 lb/ft² × 32 ft². Actual mill weight varies with thickness tolerance.

Is 18 gauge stainless steel the same thickness as 18 gauge in other metals?

No. At 18 gauge the charts give 0.0478 in for carbon steel, 0.0500 in for stainless steel, 0.0403 in for aluminum and 0.0516 in for galvanized steel.

Why is 18 gauge stainless steel 0.0500 in thick?

Stainless sheet follows the older U.S. Standard Gauge progression, which divides the nominal weight by 40 lb/ft² per inch: 2.000 ÷ 40 = 0.0500 in. Carbon steel divides the same nominal weight by 41.82 and gets 0.0478 in. ASTM A480 discourages gauge numbers, so order stainless by decimal thickness.