Pipe NPS vs OD vs Schedule
By Hamza Bin Maqsood · · 4 min read
NPS is a label, OD is fixed, schedule sets the wall: with the exact STD/Sch 40 and XS/Sch 80 overlaps.
NPS is a label, not a measurement
A 2 inch pipe is not 2 inches across. Nominal Pipe Size (NPS) is a label, and for NPS 1/8 through 12 the outside diameter (OD) is larger than the number. NPS 2 has a 2.375 in (60.3 mm) OD. Only from NPS 14 upward does the OD equal the NPS. The sizes date from when pipe was named for its approximate inside diameter; as wall thicknesses changed, the OD was held fixed so that threads and fittings kept fitting.
| NPS | OD (in) | OD (mm) |
|---|---|---|
| 1/2 | 0.840 | 21.3 |
| 3/4 | 1.050 | 26.7 |
| 1 | 1.315 | 33.4 |
| 1 1/2 | 1.900 | 48.3 |
| 2 | 2.375 | 60.3 |
| 3 | 3.500 | 88.9 |
| 4 | 4.500 | 114.3 |
| 6 | 6.625 | 168.3 |
| 8 | 8.625 | 219.1 |
| 10 | 10.750 | 273.1 |
| 12 | 12.750 | 323.8 |
Schedule sets the wall
For a given NPS the OD never changes. The schedule sets the wall thickness, and the inside diameter follows: ID = OD − 2 × wall. NPS 2 shows the pattern: Sch 10 has a 0.109 in wall and 2.157 in ID, Sch 40 has a 0.154 in wall and 2.067 in ID, Sch 80 has a 0.218 in wall and 1.939 in ID, Sch 160 has a 0.344 in wall and 1.687 in ID and XXS has a 0.436 in wall and 1.503 in ID.
Inside diameter is not the NPS either
The bore is the OD minus twice the wall, so it changes with schedule. For Schedule 40 the inside diameters of NPS 1/2, 3/4, 1, 1 1/2, 2, 3 and 4 are 0.622, 0.824, 1.049, 1.610, 2.067, 3.068 and 4.026. NPS 2 Sch 40 is 2.067 in inside, not 2.000 in, and Sch 80 narrows it to 1.939 in. The smaller bore cuts the flow area of NPS 2 from 3.36 in² at Sch 40 to 2.95 in² at Sch 80, a drop of 12%. Flow calculations need the real ID for the schedule in the design.
STD, XS and XXS
Three older names, standard (STD), extra strong (XS) and double extra strong (XXS), overlap the schedule numbers only partly.
- STD equals Sch 40 from NPS 1/8 through NPS 10. At NPS 12, STD is 0.375 in and Sch 40 is 0.406 in.
- XS equals Sch 80 from NPS 1/8 through NPS 8. At NPS 10 and 12, XS is 0.500 in, thinner than Sch 80 (0.594 and 0.688 in).
- XXS is thicker than Sch 160 through NPS 6. From NPS 8 the order reverses: Sch 160 is 0.906 in against XXS at 0.875 in.
| NPS | STD | Sch 40 | XS | Sch 80 | Sch 160 | XXS |
|---|---|---|---|---|---|---|
| 6 | 0.280 | 0.280 | 0.432 | 0.432 | 0.719 | 0.864 |
| 8 | 0.322 | 0.322 | 0.500 | 0.500 | 0.906 | 0.875 |
| 10 | 0.365 | 0.365 | 0.500 | 0.594 | 1.125 | 1.000 |
| 12 | 0.375 | 0.406 | 0.500 | 0.688 | 1.312 | 1.000 |
Not every combination exists
ASME B36.10M does not list a wall for every size and schedule. NPS 1/8, 1/4 and 3/8 have no Sch 160 or XXS, and NPS 3 1/2 has no Sch 160. The calculators on this site show a dash instead of inventing a value. At NPS 8 the walls run from 0.148 in (Sch 10) through 0.322 in (Sch 40) and 0.500 in (Sch 80) to 0.906 in (Sch 160).
Reading a pipe callout
A call such as "NPS 2 Sch 40, ASTM A53 grade B" carries two separate pieces of information. The size and schedule give the dimensions in the tables above. The ASTM specification and grade give the material, manufacturing method and tests. Two pipes with the same schedule can differ in strength or finish, and two pipes of the same grade can differ in wall, so check both parts before ordering.
Pipe versus tube
Tube is sized by its actual OD, so 2 in tube is 2.000 in across, 0.375 in smaller than NPS 2 pipe. Mixing the two on a drawing is a common error. Say "NPS 2 Schedule 40 pipe" or "2.000 in OD tube" and give the wall.
Weight
Plain-end weight is π × (OD − wall) × wall × density, which for carbon steel is 10.69 × (OD − wall) × wall lb/ft in inches. ASME B36.10M carbon steel dimensions are the basis here; stainless pipe is also made to ASME B36.19M with its own S-schedules, so check that standard for stainless sizes. NPS 2 Sch 40 weighs 3.66 lb/ft and Sch 80 5.03 lb/ft. Delivered weight differs: ASTM A53 allows ±10% on weight and a wall as low as 87.5% of nominal. Use the pipe schedule calculator for any size.
Related calculators and pages
Questions about this guide
Why is 2 inch pipe 2.375 inches across?
NPS 2 is a nominal label. The standardized OD for NPS 2 is 2.375 in (60.3 mm), and it stays the same for every schedule. Only the wall and inside diameter change.
Is STD the same as Schedule 40?
Yes from NPS 1/8 through NPS 10. At NPS 12, STD is 0.375 in and Schedule 40 is 0.406 in.
Is XS the same as Schedule 80?
Yes from NPS 1/8 through NPS 8. At NPS 10 and 12, XS is 0.500 in, thinner than Schedule 80.
What is the difference between pipe and tube?
Pipe is sized by nominal pipe size and schedule; tube is sized by its actual outside diameter and wall. 2 in tube is 2.000 in across; NPS 2 pipe is 2.375 in.
More guides
- Why 16 Gauge Is Not One Thickness Four gauge charts, four thicknesses for the same number, with the exact 7–30 gauge tables and the formulas behind them.
- Calculating Metal Weight by Hand: Formulas and Density The volume × density method for plate, bar and pipe, worked examples, and why tools differ between 7,850 and 7,870 kg/m³.
- Sheet vs Plate vs Gauge: What to Call and How to Order The thickness and width thresholds that separate sheet, strip and plate in each metal, and how to write an unambiguous order.
- Theoretical vs Delivered Weight: Mill Tolerances How rolling and pipe tolerances (ASTM A6, A480, A53) and coatings make real weight differ from the calculated figure.
This guide is general information, not engineering advice. Check dimensions and weights against the governing standard and your supplier's mill certificate, and use a qualified engineer for structural, pressure or safety-critical work.