Skip to content
StockGauge Metal gauge · plate · bar · pipe

Sheet vs Plate vs Gauge: What to Call and How to Order

By Hamza Bin Maqsood · · 4 min read

The thickness and width thresholds that separate sheet, strip and plate in each metal, and how to write an unambiguous order.

Sheet, strip and plate are product forms

Gauge, sheet and plate describe different things. Gauge is a thickness chart that exists only for thin material. Sheet, strip and plate are product forms with their own standards, thickness ranges and tolerance tables, and the boundary between them depends on the metal and the width.

The thresholds

MetalStandardSheet or stripPlate
Carbon steelASTM A6, A1011Up to 0.230 in (hot-rolled sheet and strip, A1011)Over 8 in wide and at least 0.230 in thick, or over 48 in wide and at least 0.180 in
Stainless steelASTM A480Under 3/16 in and 24 in or wider (sheet); under 24 in wide (strip)3/16 in (0.1875) or thicker and over 10 in wide
AluminumASTM B2090.006 to 0.249 in0.250 in and thicker

Carbon steel

ASTM A6 covers rolled structural plate. It treats flat product as plate when it is over 8 in wide and at least 0.230 in thick, or over 48 in wide and at least 0.180 in thick. Thinner hot-rolled sheet and strip fall under standards such as ASTM A1011, and cold-rolled sheet under A1008. Light carbon steel is typically ordered by gauge or decimal thickness; heavier material is ordered by fraction.

Stainless steel

ASTM A480 calls material plate when it is 3/16 in (0.1875) or thicker and over 10 in wide. Sheet is thinner than 3/16 in and at least 24 in wide, and strip is narrower than 24 in. The threshold is lower than for carbon steel: 3/16 in stainless is plate, while 3/16 in carbon steel is plate only when it is wider than 48 in. A480 also discourages gauge numbers.

Aluminum

ASTM B209 covers aluminum and aluminum-alloy sheet and plate. Sheet runs from 0.006 in up to 0.249 in; plate begins at 0.250 in. Aluminum is therefore sheet at 0.1019 in (10 gauge, Brown & Sharpe) and plate at 1/4 in. The whole 7 to 30 gauge chart, from 0.1443 to 0.0100 in, sits inside the sheet range.

Where gauge stops

The gauge charts here run from 7 to 30. The thickest carbon steel entry is 7 gauge at 0.1793 in, just under 3/16 in, and the thickest aluminum entry is 0.1443 in. Beyond that, thickness is stated as a fraction or a decimal. Write 0.1875 rather than 0.19 for 3/16 in, because rounding a fraction can move the thickness by several thousandths and the weight with it.

The same thickness in different metals

At 1/4 in all three metals are plate, but the weights differ widely. A 4×8 ft sheet weighs 327 lb in carbon steel, 333 lb in stainless steel and 112 lb in aluminum, using 7,850, 8,000 and 2,700 kg/m³. Per square foot that is 10.21, 10.40 and 3.51 lb. A weight estimate should always name the metal, not just the thickness.

Why it matters when you order

  • Sheet, strip and plate each have their own tolerance tables. Plate under ASTM A6 and A480 may be 0.01 in under the ordered thickness, with the over-tolerance depending on width and thickness, so the same nominal size can deliver a different weight in a different form.
  • Prices, minimum quantities and available lengths can differ between sheet, strip and plate, so one thickness may be priced differently depending on the form.
  • A gauge number leaves both the metal and the chart ambiguous: 0.0598, 0.0625, 0.0508 and 0.0635 in are all "16 gauge".

Writing a clear order line

State the metal and product standard, the thickness in decimals and the dimensions. Examples:

  • ASTM A36 plate, 0.250 in × 48 in × 96 in
  • ASTM A240 type 304 sheet, 0.0625 in × 48 in × 96 in
  • ASTM B209 5052-H32 sheet, 0.063 in × 48 in × 96 in
  • ASTM A1008 cold-rolled sheet, 0.0598 in (16 gauge MSG) × 48 in × 96 in

Then convert the thickness to weight with the sheet and plate calculator before you compare quotes, and check the 4×8 weight chart for freight planning.

Condition and grade

Thickness and form are only part of an order line. The condition (hot-rolled, cold-rolled, pickled and oiled), the grade or alloy and temper, the edge condition, the quantity and whether the supplier cuts to size all affect price and tolerance. When two quotes differ by more than the weight difference explains, compare these details before choosing the cheaper one.

Related calculators and pages

Questions about this guide

At what thickness does aluminum sheet become plate?

Under ASTM B209, aluminum sheet runs from 0.006 in to 0.249 in and plate starts at 0.250 in.

At what thickness does stainless steel sheet become plate?

ASTM A480 treats stainless as plate at 3/16 in (0.1875) and thicker when over 10 in wide. Thinner material 24 in or wider is sheet, and narrower material is strip.

When is carbon steel plate rather than sheet?

ASTM A6 treats flat-rolled carbon steel as plate when it is over 8 in wide and at least 0.230 in thick, or over 48 in wide and at least 0.180 in thick. Thinner hot-rolled sheet and strip fall under standards such as A1011.

How should I specify thickness on an order?

Give the metal, the product standard and the thickness in decimal inches or millimetres, for example "ASTM A240 type 304 sheet, 0.0625 in × 48 in × 96 in", rather than a gauge number.

This guide is general information, not engineering advice. Check dimensions and weights against the governing standard and your supplier's mill certificate, and use a qualified engineer for structural, pressure or safety-critical work.